Two-notes Reload Instrukcja Użytkownika Strona 22
- Strona / 51
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Connecting the Torpedo Reload
• as the impedance does not change with the attenuation, the tone of your amp stays the same;
• the volume you hear in the room can be set continuously, you get REAL master-volume control
(SPEAKER parameter), after your amplifier’s master volume;
• the speaker-output impedance of your amplifier is independent from the speaker impedance
of the actual speaker cabinet you plug on the Torpedo Reload. This opens up a great many fun
possibilities of cabinet mixing.
4.2 Connection
Connecting the Reload as an attenuator is really quite simple, provided you observe the following:
• Always match the value of the impedance on the Torpedo Reload (either 4, 8 or 16 Ohms) to
your amplifier’s speaker-output impedance.
• The Torpedo Reload will normally get warm during use, so you must not put it in a closed box or
obstruct the air vents.
• You can connect one or two cabinets to the Torpedo Reload, or no cabinet at all if you want
to use the loadbox only (silent playing and recording).
• The impedance of the cabinets you may plug to your amp is independent from the impedance
of that amplifier. You can very well use the 8-Ohm speaker output of your amp while having one
8-Ohm cabinet and another 16-Ohm cabinet plugged to the Torpedo Reload! Please refer to
"Possible post-attenuation speaker combinations", Part 7.2.3 for more information about cabinet
matching.
1. Connect your amplifier’s
speaker out to the Torpedo
Reload’s SPEAKER IN.
2. Make sure the impedance se-
lected on the Torpedo Reload
matches the value at your
amp’s output.
3. Connect a cabinet to the
lower SPEAKER OUT jack.
4. Connect a second cabinet,
if needed, to the higher
SPEAKER OUT jack.
The loadbox inside the Torpedo Reload remains active whether you
have plugged a cabinet to it or not. We recommend using amplifiers
with a maximum power rating of 150 W RMS (200 W peak). Basically,
the loadbox turns your amplifier’s power into heat. If the temperature
inside the Torpedo Reload is too high due to an excess of power, DO
NOT WORRY: the active security system will put your amp on a safe
security load, while the Torpedo Reload cools down.
22 Two Notes Audio Engineering Torpedo Reload
- Torpedo Reload 1
- Contents 5
- Foreword 7
- 2 Declaration of conformity 8
- 3 Contents of the package 9
- European Union 9
- 5 Warranty 10
- 1 What is a loadbox? 11
- About the Torpedo Reload 13
- 2 Front panel 14
- 3 Rear panel 14
- 4.1 RE-ACT™ 15
- 4.2 Hi-Z instrument DI 15
- 4.3 REPLAY™ 15
- 4.4 MATCH™ 16
- 6.1 Tube Stage Output 17
- 6.2 Post FX section 18
- 6.3 The new Wall of Sound III 18
- Connecting the Torpedo Reload 19
- 2 LED indicators 20
- 3 DI recording 20
- 4.2 Connection 22
- 4.3 Contour 23
- 5.1 Silent REPLAY™ 24
- 5.3 MATCH™ 25
- 1 Installation 27
- ON OFF OFF ON ON 29
- OFF OFF ON 29
- Using Torpedo Wall of Sound 31
- 4 General controls 33
- 6 Presets 34
- 7 Power Amp 35
- 9 Miking 36
- 11 Exciter 37
- 13 Setup 38
- 14 Wall of Sound section 39
- 15 Want more cabs? 40
- 16 Hotkeys 41
- Specifications 43
- 2.1 Internal circuit diagram 45
- 2.2 Audio connections 45
- 2.5 Technical data 47
- Technical support 49
Powiązane produkty i podręczniki dla Audio Two-notes Reload
Audio Two-notes Reload Instrukcja Użytkownika
(51 strony)
(51 strony)
GE 52044 GE Seven-Day Plug-In Timer with Cove manuali
Manuali dei proprietari e guide per l'utente per Orologio GE 52044 GE Seven-Day Plug-In Timer with Cove.
We fornisce 1 manuali pdf GE 52044 GE Seven-Day Plug-In Timer with Cove per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentarze do niniejszej Instrukcji